大型工業涂板機

設備用途：適用于鉛銻、鉛鈣合金板柵涂填粘性或砂性鉛膏及表面干燥設備構成：自動上板裝置、涂板主機、淋酸壓板裝置、表面干燥機、控制系統。Application:ItisusedtopastetheviscousorsandypasttothePb-SbandPb-Cagridsanddrythegrids.Composition:Autoplatefeedingdevice,pastingmachine,drenchingandpressingdevices,facialdrierandcontrolpanel.性能、特點：○涂板機板柵采用機械自動送給，設有手動板柵寬度調整機構。設有無板柵或重疊板柵狀態時自動斷開裝置。○涂膏斗有獨立的調速馬達，膏斗出口處采用反向運動鋼輥，精確控制涂膏量。○膏斗設有可傾離開機構，便于操作者清理和排除涂板故障。○采用水平帶式連續涂填鉛膏運動;傳動機構采用無級調速;氣缸調整傳送帶漲緊力，維修換帶方便。○設有可調整壓力的橡膠輥筒，完成涂板后的壓板和表面壓酸要求。○板柵間多余的鉛膏，有專門回收裝置。○設備啟、停控制按扭在機臺上板處安裝，并按防酸、水技術標準配置。Performance&Features○Thepastingmachineissuppliedwithauto-feedingdevice,thepastingwidthcanbeadjustedbyhand,themachinecanbestoppedifthereisnogridoroverlapping.○Thereisaindependentmotorforthepasthopper,thesupplyrollersisruninoppositedirectiontoaccuratelycontrolthepastweight.○Thehoppercanbeleftintilttofacilitatetheoperatortoobserveandmaintainfault.○Themachineusesthecontinuouspastingbeltwithtransmissionandtensionsystem,itiseasytomaintainandexchange.○Thepressureofrubberrollerisadjustabletopresstheplateswithacid.○Thepastontheconveyorbeltisremovedandstoredbyspecialfacilities..○TheON/OFFbuttonsareinstalledinaccordancewithacidproofandwaterproofstandards.

關鍵詞：

大型工業涂板機

所屬分類：

產品咨詢：

產品描述

設備用途：適用于鉛銻、鉛鈣合金板柵涂填粘性或砂性鉛膏及表面干燥

設備構成：自動上板裝置、涂板主機、淋酸壓板裝置、表面干燥機、控制系統。

Application: It is used to paste the viscous or sandy past to the Pb-Sb and Pb-Ca grids and dry the grids.

Composition: Auto plate feeding device, pasting machine, drenching and pressing devices, facial drier and control panel.

性能、特點：

○涂板機板柵采用機械自動送給，設有手動板柵寬度調整機構。設有無板柵或重疊板柵狀態時自動斷開裝置。

○涂膏斗有獨立的調速馬達，膏斗出口處采用反向運動鋼輥，精確控制涂膏量。

○膏斗設有可傾離開機構，便于操作者清理和排除涂板故障。

○采用水平帶式連續涂填鉛膏運動;傳動機構采用無級調速;氣缸調整傳送帶漲緊力，維修換帶方便。

○設有可調整壓力的橡膠輥筒，完成涂板后的壓板和表面壓酸要求。

○板柵間多余的鉛膏，有專門回收裝置。

○設備啟、停控制按扭在機臺上板處安裝，并按防酸、水技術標準配置。

Performance & Features

○ The pasting machine is supplied with auto-feeding device, the pasting width can be adjusted by hand, the machine can be stopped if there is no grid or overlapping.

○ There is a independent motor for the past hopper, the supply rollers is run in opposite direction to accurately control the past weight.

○ The hopper can be left in tilt to facilitate the operator to observe and maintain fault.

○ The machine uses the continuous pasting belt with transmission and tension system, it is easy to maintain and exchange.

○ The pressure of rubber roller is adjustable to press the plates with acid.

○ The past on the conveyor belt is removed and stored by special facilities..

○ The ON/OFF buttons are installed in accordance with acid proof and water proof standards.